MIL-P-80041D
(Non-Government standards and other publications are normally available
from the organizations that prepare or distribute the documents. These
documents also may be available in or through libraries or other informational
services.)
In the event of a conflict between the text of
2.3 Order of precedence.
this document and the references cited herein, the text of this document takes
precedence.
Nothing in this document, however, supersedes applicable laws and
regulations unless a specific exemption has been obtained.
REQUIREMENTS
3.
When specified (see 6.2), one complete press shall be
3.1 First article.
s u b j e c t e d t o f i r s t article inspection (see 6.4) in accordance with 4.4.
3.2
Design.
The
press
shall
be
new
(not
a
prototype)
and
one
of
the
m a n u f a c t u r e r s c u r r e n t p r o d u c t i o n m o d e l s c a p a b l e o f o p e r a t i o n s i n accordance
with the requirements herein.
The press shall be of the inclinable gap or "C"
type frame design, and shall provide power to dies used for forming, blanking,
or shaping metal and non-metallic parts.
All components, parts, and features
n e c e s s a r y to meet the performance
specified herein shall be provided.
Parts
subject to wear, breakage, or distortion shall be accessible for adjustment,
replacement, or repair.
3.2.1 Measuring and indicating device calibration.
Measuring and indicat-
i n g d e v i c e s s h a l l b e graduated i n Inch-pound ( s e e 6 . 5 . 1 ) , m e t r i c ( s e e 6 . 5 . 2 ) ,
or dual (inch-pound and metric) units as specified by the procuring a c t i v i t y
(see 6.2).
Regardless
o f t h e m e a s u r e m e n t s y s t e m used,
a l l m e a s u r i n g and
indicating devices on the machine shall be graduated in the same system.
The press m a y contain
reclaimed materials to
3.2.2 Reclaimed materials.
the maximum extent p o s s i b l e p r o v i d e d s u c h m a t e r i a l s w i l l n o t j e o p a r d i z e t h e
i n t e n d e d use, performance, or design
life of the press.
Reclaimed materials
s h a l l have been
collected or recovered from solid waste
and reprocessed to
become a source of raw materials, as opposed to virgin raw materials.
None of
the above shall be interpreted to mean that the use of used, rebuilt, or
remanufactured end products are allowed under this specification.
3.2.3 Energy e f f i c i e n c y .
The press and its components that
directly
consume energy
in normal
for
operation
shall be designed and constructed
energy efficiency in
a c c o r d a n c e with the developments
a v a i l a b l e w i t h i n the
industry.
3.2.4 Controls.
All operating controls shall be located convenient to the
operator's work station(s).
3.2.5 Safety and health requirements. All parts, components, mechanisms,
a n d assembles furnished on
t h e press, whether
or not specifically required
herein, shall conform with all requirements of 29 CFR 1910 and ANSI B11.1. If
a conflict arises
between 29 CFR 1910 and B11.1, 29 CFR 1910 shall apply.
Additional safety and health requirements shall be as specified in detail (see
6 . 2 ) . C o v e r s , g u a r d s , o r o t h e r s a f e t y d e v i c e s n o r m a l l y f u r n i s h e d a s standard
on the manufacturer's commercial press supplied to the commercial market shall
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business