MIL-P-80041D
that
be provided for the point of operation and all other parts of the press
present safety hazards. Additional guarding dependent on workpiece size and
and fully described by the
b e p r o v i d e d w h e n specified
configuration shall
procuring activity (see 6.2).
3 . 2 . 6 M e r c u r y r e s t r i c t i o n . The press shall not contain mercury or mercury
compounds nor be exposed t o f r e e m e r c u r y d u r i n g m a n u f a c t u r e .
Asbestos
and
materials
containing
asbestos
3.2.7 Asbestos restriction.
shall not be used on or in the press.
o p e r a t i o n , ser -
D u r i n g the m a n u f a c t u r e ,
3.2.8 Environmental protection.
vice, transportation, or storage of the press, and its components, materials
hazardous to the ecological system as prohibited by Federal, state, or local
installation on the date of the contract
statutes in effect at the point of
shall not be used or emitted.
3.2.9 Lubrication.
Unless otherwise specified (see 6.2), an automatic oil
lubricating system shall be provided for all parts and mechanisms requiring a
continuous flow of lubricating oil.
When specified (see 6.2), an automatic
r e c i r c u l a t i n g s y s t e m s h a l l b e f u r n i s h e d . Mechanisms requiring periodic manual
lubrication shall be readily accessible for servicing.
To provide for replacement of worn parts, all
3.2.10 Interchangeability.
parts shall be manufactured to definite dimensions and tolerances that will
permit installation of replacement parts without modification of the part or
machine. A l l r e p l a c e m e n t p a r t s s h a l l b e i n t e r c h a n g e a b l e w i t h t h e i r r e s p e c t i v e
o r i g i n a l p a r t s , and fit/function with mating components.
The press shall be constructed of parts which are new,
3.3 Construction.
without defects, a n d f r e e o f r e p a i r s . The structure s h a l l w i t h s t a n d a l l
f o r c e s e n c o u n t e r e d d u r i n g o p e r a t i o n o f t h e p r e s s t o i t s m a x i m u m rating and
capacity without permanent distortion, or failure.
3.3.1 Castings and forgings.
All castings and forgings shall be free of
d e f e c t s , s c a l e , and mismatching.
No processes such as welding, peening, plug-
ging, or filling with solder or paste shall be used for reclaiming any defec-
and
tive part.
Such processes may be used o n l y f o r e n h a n c i n g s u r f a c e f i n i s h
appearance.
3 . 3 . 2 F a s t e n i n g d e v i c e s . A l l f a s t e n e r s s h a l l b e i n s t a l l e d t o prevent
change of tightness. Fastening devices subject to removal or adjustment shall
n o t be permanently
installed.
3.3.3 Surfaces. All surfaces shall be clean and free of harmful or
All edges shall be either rounded or beveled unless
extraneous materials.
sharpness is required to perform a necessary function. Except as otherwise
specified herein, t h e c o n d i t i o n a n d f i n i s h o f a l l s u r f a c e s s h a l l b e i n
accordance with the manufacturer's commercial practice.
3 . 3 . 4 Welding , b r a z i n g , o r s o l d e r i n g .
Welding, brazing, or soldering shall
None of these
be employed o n l y w h e r e s p e c i f i e d
in the original design.
operations
shall
be
employed
as
repair
measure
for
any
defective
part.
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business